C1611 - Front Wheel Sensor Short Circuit To Ground or Open Circuit
C1611 - Front Wheel Sensor Short Circuit To Ground or Open Circuit - Fault - CM8; CR8; CS8; DR5; DS5; HF8; HG8; HJ8; HK8; HL8; LG1; LGX; LJ2; LK2; LL1; PB1; PJ1; PJZ; PM1; PR1; PRC; PS1; PSC; PX1; PXC; PY1; PYC
Fault Code | Possible cause | Action |
|---|---|---|
C1611 | Front wheel sensor short circuit to ground or open circuit | Make sure the ABS ECM connector is secure. Make sure the wheel speed sensor connector is secure. Disconnect ABS ECM connector and proceed to pinpoint test 1: |
Subheading - Pinpoint Test
Pinpoint Tests
C1611 - Front Wheel Sensor Short Circuit To Ground or Open Circuit - Pinpoint Test -LG1; LGX; LJ2; LK2; LL1
Test | Result | Action | |
|---|---|---|---|
1 | Check cable and terminal integrity: - ABS ECM connector pin 17 and ABS ECM connector pin 8 - Sensor connector pin 1 - Sensor connector pin 2 | OK | Proceed to test 2 |
Faulty | Rectify fault, proceed to test 9 | ||
2 | Check cable for short circuit: - ABS ECM connector pin 8 and ground | OK | Proceed to test 4 |
Short circuit | Proceed to test 3 | ||
3 | Disconnect the front wheel speed sensor connector. Check cable for short circuit: - Wheel speed sensor connector pin 2 (motorcycle harness side) and ground | OK | Replace the wheel speed sensor, proceed to test 9 |
Short circuit | Locate and rectify wiring harness fault, proceed to test 9 | ||
4 | Check cable for short circuit: - ABS ECM connector pin 17 and ground | OK | Proceed to test 6 |
Short circuit | Proceed to test 5 | ||
5 | Check cable for short circuit: - Wheel speed sensor connector pin 1 (motorcycle harness side) and ground | OK | Replace the wheel speed sensor, proceed to test 9 |
Short circuit | Locate and rectify wiring harness fault, proceed to test 9 | ||
6 | Check cable continuity: - ABS ECM connector pin 8 and wheel speed sensor connector pin 2 (motorcycle harness side) | OK | Proceed to test 7 |
Open circuit | Locate and rectify wiring harness fault, proceed to test 9 | ||
7 | Check cable continuity: - ABS ECM connector pin 17 and wheel speed sensor connector pin 1 (motorcycle harness side) | OK | Proceed to test 8 |
Open circuit | Locate and rectify wiring harness fault, proceed to test 9 | ||
8 | Reconnect the front wheel speed sensor connector. Check the wheel speed sensor operation: - Connect a suitable voltage supply between 10 V and 16 V between ABS ECM connector pin 8 (negative) and pin 17 (positive), and measure the current consumption of the wheel speed sensor | 1.8 mA to 16.8 mA | Proceed to test 9 |
Faulty | Replace the wheel speed sensor, proceed to test 9 | ||
9 | Reconnect ABS ECM harness, clear fault code and test ABS to verify fault cleared. | OK | Action complete - quit test |
Fault still present | Contact Triumph service | ||
Subheading - Resistance Data
Resistance Data
C1611 - Front Wheel Sensor Short Circuit To Ground or Open Circuit - Resistance Data - PB1, PJ1, L*1; PV1;HG8;HJ8;HK8;HL8
Wheel speed sensor current consumption data under typical conditions:
Supply Voltage | Min | Typical | Max |
|---|---|---|---|
10 - 16 V | 1.8 mA | 7.5 mA | 16.8 mA |
Subheading - Circuit Diagram
Circuit Diagram
C1611 - Front Wheel Sensor Short Circuit To Ground or Open Circuit - Circuit Diagram - LG1; LGX
|